Table of Contents
Panel Lock Press TEMP+ or TEMP- pad followed by QUIET SOAK pad to lock. Then press TEMP+ or TEMP- pad followed by QUIET SOAK pad to unlock.
Why is my hot tub panel not working?
Bottom line is – it could be a bad spaside control panel, or it could be a bad spa control board, or a bad cable that runs between the control panel and the control board. Or it could be fuse on the circuit board or the transformer, not sending the correct power to the topside panel.
Is there a reset on my hot tub?
There are generally two “hard resets” in hot tubs, the GFCI, and the high limit reset. The GFCI pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.
How do you unlock control panel?
Steps to lock and unlock the control panel on your computer are provided below. Use Group Policy to Lock and Unlock Access to Control Panel. Type gpedit.msc on Run (Press [Windows] and [R] to open Run window) Unlock and Lock Control Panel From Windows Registry.
How do I know if my hot tub control panel is bad?
If the control panel is frozen or dead, you have to check if the problem is the control panel or the circuit board. Examine if there is moisture in the display. Check if there are cracked buttons or if a part is wet. If only a part is not working, look for error messages or blinking lights.
How do I reset my MSPA hot tub?
Locate the spa’s high-limit reset. This is a red button found on many spa packs. Press the high-limit reset button. Turn on your spa and observe its operation. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
How do I know if my hot tub circuit board is bad?
If you DO have 220 volts across both hot wires coming from the house, then next measure the voltage across both heating element pins. You should see 220 volts. If you do not, then the circuit board is faulty and will need to be replaced or sent to us for repair.
What does E1 mean on MSPA?
If the filters are used for too long they will get dirty and deteriorate, meaning the quality of water is not being maintained effectively. Dirty filters can also cause F1/E1 errors to appear on the pump. If you are unable to clean the filters, these should be replaced.
Why is my MSPA not heating up?
If your hot tub won’t heat the water properly, it could be the heater element or low flow from your pump. Most heating failure result from corrosion caused by low PH in water supply. Any PH below 7.0 damages the heating element and trips the GFCI breaker.
How do you unlock Balboa in hot tub control panel?
Spas using Balboa control systems To unlock the panel, while holding down the “Temperature” button (or the “Up” button if you do not have the “Temperature” button), gently press and release the “Light” button twice.
How do you unlock a stove panel?
To unlock an oven, hold down the Lock button on your control panel for 2 or 3 seconds and wait for the oven to beep to indicate it’s unlocked. If this doesn’t work, unplug it from the electrical outlet and wait a few minutes. Then, plug it back in again, which may reset the temperature gauge and cause it to unlock.
How do you unlock the Catalina spa control panel?
To unlock the panel, press “Time” “Jets 1” then “Cool.” Press “Warm” or “Cool” then “Time,” “Jets 1,” and “Warm” within 3 seconds to activate the lock. The TL indicator light will light when the set temperature is locked.
What is lock in hot tub?
The spa lock feature is designed to lock the control panel so others can’t mess with the lights, jets, and temperature settings. It’s a useful feature if you like things a certain way and are the only one using the hot tub on a regular basis.
How long does a hot tub control panel last?
That said, most topside spa panels will last 10 years. If you have had repeated and mysterious failures to the pcb every few years, it may be a good time to replace the entire spa pack. New spa packs are less prone to circuitry problems. If your spa pack and control is over 20 years old – it’s a good time to upgrade!.
Why is my hot tub control panel flashing?
Ensure the hot tub is heating. If the hot tub is not heating, the light is blinking because the water temperature has dropped more than 2 degrees from the set temperature. If the hot tub is not equipped with either salt water system, power the tub off at the breaker or unplug.
How do I fix the HH code on my hot tub?
Open the spa cover and let the spa cool down for 10 minutes, then touch the control panel to reset the circuits, or push a red reset button on air systems. For OH, HH or HOT trouble codes, an overheating hot tub is not usually a heater problem. It is almost always a flow problem.
How do you reset hot tub after power outage?
A GFCI is required in all spa installations. It is a micro-circuit breaker, much more sensitive to voltage fluctuations than a normal circuit breaker. If the GFCI has been tripped by a power surge or brownout, just pressing the “RESET” button, if there is one, will turn the circuit, and your hot tub, back on.
