QA

How To Replace A Thermocouple In A Gas Fireplace

How do you change a thermocouple on a gas fireplace?

Procedure for Replacing a Thermocouple Turn off the gas supply to the gas valve. Use the wrench to unscrew the connector that holds the thermocouple to the gas valve, then unhook the probe from its clip and pull out the entire thermocouple assembly. Take the thermocouple to the hardware store to purchase a new one.

How much does it cost to replace a thermocouple in a gas fireplace?

When replacing a thermocouple or thermopile with the help of a professional, you can expect to pay between $150 and $250.

Can you replace a thermocouple yourself?

1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Then detach the thermocouple from the burner and take it with you to the home center or hardware store to ensure you buy the right replacement.

How do I know if my thermocouple is bad on my gas fireplace?

The Fix: Pilot Light to Gas Fireplace Won’t Stay Lit So you’ve checked your pilot light and even reset it, but still, it wont stay lit. This can be an indication that your fireplace thermocouple is either bad or worn out.

How long does a fireplace thermocouple last?

Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.

How much should a plumber charge to replace a thermocouple?

Hot water heater repair cost Service Average cost to repair Leak repairs $100 – $1,000 Pilot light replacement $50 – $200 Pressure relief valve replacement $50 – $300 Thermocouple replacement $100 – $325.

How much is a new thermocouple?

It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on. It will shut the gas off if it’s not.

Can you clean a thermocouple?

Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up.

What makes a thermocouple go bad?

Soot buildup on the thermocouple may block the flame. Under constant exposure to a hot flame, a thermocouple wears down over time. Even a slight residue can make the thermocouple malfunction.

Are thermocouples universal?

Honeywell, White Rodgers, and other manufacturers make universal replacement thermocouples, usually with a 30-millivolts (mV) rating for standing-pilot furnaces. Electronic flame sensors are much less universal, and you must find the exact part specified for your furnace model.

How do you bypass a thermocouple?

To bypass the thermocouple: Move the tilts switch wire aside. Remove your thermocouple from the heater using an 8mm wrench. Pull the valve housing aside using your 13mm socket wrench. Remove the valve using your pliers. Put your thermocouple back into position.

Why will my gas fireplace not stay lit?

The thermocouple and thermopile are the two most common reasons why a gas fireplace won’t stay lit. However, there are other possibilities out there. Another common culprit is incorrect gas pressure. As the seasons pass, you may find that your gas pressure drops below where it needs to be.

Should thermocouple be in pilot flame?

The pilot flame should touch the thermocouple at a specific level. If the flame is blue and weak, and barely reaches the thermocouple, it needs to be stronger. If it extends well above the thermocouple, it’s too strong. Install a new thermocouple by screwing it in, heating it up a bit, and then lighting the pilot.

What happens if a thermocouple fails?

Normally when the thermocouple malfunctions or isn’t working, it simply shuts off the gas to your heater. This is important, particularly if the pilot light is out, because it prevents harmful gas from leaking into your home.

Can thermocouples go bad?

Like the other component parts in your furnace, the thermocouple can wear down over time, producing lower voltage than it should when heated. And the worst part is that you can have a bad thermocouple without even knowing. Therefore, inspecting and testing your thermocouple should be part of your furnace maintenance.

Why won’t my logs catch fire?

If your logs won’t catch fire, it may be that you have started too big. Light some kindling wood or paper first, and wait for it to catch fire to some small logs or pieces of coal. If you overload your wood burner with logs, the lack of air circulation can also cause your fire to go out.

What do thermocouples do?

Thermocouples are sensors used to measure temperature. A thermocouple consists of two wires, or wire legs, made from different metals. The legs are welded together at one end, into a junction, where the temperature is measured. A voltage is created when the junction senses a change in temperature.

What would cause pilot light to go out?

Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.